The program will only work on one computer for which you will receive a license key.
Original program (100% reset Waste Ink Pad counters)īinds to HardWare ID PC (you can reinstall Windows) The program resets the counters: Main pad counterĪttention! The program is attached to a PC
The program works only with USB on the OS: Windows Turn printer on and off 5 times using Power button.Epson L110, L210, 元00, 元50, 元55, L550, L555 (EURO, CIS) Ver.1.0.8 Service Adjustment Program - is a utility program for the specified printer models, the program allows you to reset the waste ink pad counter, prescribe the print head ID, do printer initialization and other functions. Turn on printer holding the following buttons : Alt, LF/FF, Load/Eject, Micro Adjust.ĮPSON Stylus Color II, IIS, 400, 600, 640. Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led. In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink. Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Error led. Pressing and holding PAUSE, LF/FF and DOWN ARROW buttons turn on printer. In 2-3 seconds time press and hold CLEANING button for 10-12 seconds. Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button, You will see blinking INK OUT led. In 2-3 seconds time press and release CLEANING Color button, You will see leds blinking. Pressing and holding LOAD, CLEANING Color and CLEANING Black buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds. In 2-3 seconds time press and hold LOAD/EJECT button, until all leds will blink. In 2-3 seconds time press and hold CLEANING button, until all leds will blink. In 2-3 seconds time press LOAD/EJECT and CLEANING buttons again. Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds. Pressing and holding ALT+FONT+LOAD+PAUSE buttons combination, press POWER button. Then hold button one down for 10 seconds. Switch on the power holding buttons one and three (ROLL PAPER and SHEET FEEDER). The printer will cycle through and self check for about 3 minutes and then function normally.
When the paper out LED is just flashing release both buttons and press and hold the ink-cleaning button for at least 10 seconds. Hold down both the paper and ink buttons while you turn on the power. Then, on demand (you'll see message on printer screen), turn off printer. Press all following buttons : Power, B&W, Color, Press Color button to clear protection counter. Press all following buttons ower, Load/Eject, Stop, B&W, Color,Īfter this printer turns on and you'll see "Init eeprom" on printer screen. Seconds, and the printer will then change to standby mode. When the printerĬhecks the maintenance error function, the front LEDs will light for 2
Switch, and then press and hold the switch again for 10 seconds. During this time, momentarily release the roll paper Paper and Ink indicators will flash forģ seconds. Press and hold STOP, MANITENANCE and POWER buttons
Press RIGHT then UP - you must see MAIN TANK. Press DOWN, CLEAR COUNTER option should appear. Turn on power pressing and holding PAPER SOURCE,PAPER FEED,CUT/EJECT.
o si no realizar un reseteo manual - hay publicada una solución que le haría a todas las impresoras, según dice ignaciocam con título "informacion para impresora epson" - el cual puede realizarse también siguiendo las sencillas instrucciones siguientes:īelow You will find instructions to reset protection counter on older printer models manually (25 printer models).ģ) Perform reset instructions provided for Your printer model below. Luego, se puede resetear el contador, una opción es usar el programita SSC Utilitario (que a algunos les funciona, a otros no) para lo cual hay que tener instalado los controladores incluido el smart panel. Primero, lo recomendado es asegurarse de que la máquina no está goteando tinta, y que si lo está, de limpiar por lo menos los pads absorbentes que se encuentran debajo del "chasis" de la impresora. Y como lo sabe la impresora?, es que lleva un contador interno de limpieza de cabezales. Para muchos modelos quiere decir que el depósito de tinta se llenó.